![]() If the tracing worked properly, by clicking on the 'Modeling' tool, you should be able to see the vectors all around the individual parts of the traced image.įinally, to choose the desired raster input level, select all the traced elements and set the fill color through the window Object Properties (Object Properties). Then, select the elements drawn with the 'Pick tool' and use the command and use the Arrange (Arrange)> Separate (Ungroup). The original image remains behind the tracing, so select it and delete it. Make sure your traced shapes are presented in a uniform, flat color. You'll see a lot of tracing options, so do several tests until you find the one that's right for you. No need to do it by hand! You can do this simply by selecting the inserted image and using the command Bitmaps> Bitmap Trace (Bitmap Trace). If you want to insert a non-vector image in your file, you have to trace it in vector. Our making system takes into account only the drawings in vector, ignore all the images inserted in other formats (like.jpg or. You can create texts using fills for raster engravings, lines for vector engravings, or a combination of the two types of incisions. Once you run this command, you will not be able to edit the text, so do this after checking the spelling! To turn the text into curves, just select it and then choose Arrange (Arrange)> Convert to Curves (Convert to Curves) from the top menu. In this way the laser will follow your drawing correctly, even without having the same installed font. Sets the fill color as black with the RGB values of 0, 0, 0:Īll the texts inserted in your drawing must be converted into curves. ![]() ![]() Sets the fill color as gray with the RGB values of 128, 128, 128: The light raster engraving is absolutely superficial, altering the color of the material without going deep. ![]() Sets the fill color to light gray with the RGB values of 230, 230, 230: The incisions do not change according to the thickness of the material (unless otherwise indicated in the sheet). The values of the engraving depth are indicated in the "technical details" tab of each material in the catalog. To obtain a more defined border in an area engraved with a raster pattern, combines the black or gray fill with a contour corresponding to a vector engraving. Make sure you use solid and spot colors and no patterns or textures. You can use any grayscale between the two extremes, but remember that the three RGB values must be equivalent. The scale of the raster engraving goes from the black that corresponds to the most marked incision, up to the very light gray that will make the engraving lighter (or white, which corresponds to the null incision). Engraving in raster mode a thinner line will probably not lead to good results. Generally, raster fills are used for areas with backgrounds, but you can also make a raster incision of lines that have a contour with a thickness greater than 0.3mm. Sets the outline color as RGB red with values 255, 0, 0: Sets the outline color as RGB green with values 0, 255, 0: Sets the outline color as magenta RGB with values 255, 0, 255: In the window Object Properties (Object Properties) set the thickness of the contour by clicking in the 'Thickness' box (Width) and writing '0.01mm', then press enter. All three incisions are drawn very precisely with subtle lines, roughly the same size as the laser beam. There are three different levels of engraving available: light, medium and deep, each with a different intensity and therefore depth. The laser will move along the engraving lines in your drawing. The vector etching process is very similar to the cutting method, but instead of piercing the material, the laser only affects the surface. Sets the color of the outline as blue RGB with values 0, 0, 255: So, in the window Object properties (Object properties) set the thickness of the contour by clicking in the 'Thickness' box (Width) and writing '0.01mm', then press enter: To obtain a cutting line, draw a line or shape. Your file should remember that sheet with the lines drawn. The simplest way to visualize how this will turn into your project is to imagine placing on a sheet of paper the pieces you would like to make, and then draw their outline on the sheet with a pencil. The basic part of your design are the shapes you will cut. If you convert the same lines in red, the laser will engrave the bird on the chosen material, and so on. The color used for the drawn lines determines what the laser will do, whether it is a cut or an engraving.įor example, if you draw a bird with a blue outline, the laser will cut a bird.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |